MZR DISI Remanufactured Long Blocks now Available at EdgeAutosport

[Hal]

Great to hear.

[EdgeAutosport.com]

Just wanted to let you guys know that ETA's with this engine are a little bit overestimated typically. When we order one, they give us an ETA of 6 to 8 weeks, but so far every engine we have ordered has shipped from them to us within 10 business days of us placing the order.

[Mashop]

My speed only has 20k on it, but I still find it reassuring that the motor can be replaced quickly and somewhat reasonably priced. Thanks for supporting the platform.

'13 Speed3, RMM,PMM,TMM,Solid Shift Bushings, APv3, Cobb 93 map.

[dale_gribble]

Can't you guys keep at least 1of these in inventory all of the time? This option is my ace in the hole. Set up terms with vendor where you just hold their inventory on site and pay on shipment.

A lot of us would sleep better knowing a well rebuilt DISI is only 3-5 days away at any time. That's where the value and beauty of this rebuilt motor is- on demand.

6-8 weeks or even 3 weeks is going to push me in a different direction should the time come. These are our daily drivers.

[EdgeAutosport.com]

Originally Posted by dale_gribble Can't you guys keep at least 1of these in inventory all of the time? This option is my ace in the hole. Set up terms with vendor where you just hold their inventory on site and pay on shipment. A lot of us would sleep better knowing a well rebuilt DISI is only 3-5 days away at any time. That's where the value and beauty of this rebuilt motor is- on demand. 6-8 weeks or even 3 weeks is going to push me in a different direction should the time come. These are our daily drivers.

We could probably do this, however, the problem comes when 3 people buy at once and two have to wait a couple weeks anyways. Thats the problem with inventory in general though... Lol! We once had 3 cp-e cold air intakes sit on a shelf for a year and a half. Then they all sold in the same week.

[dale_gribble]

Ok stock 3 then.

[jrotaryb]

Originally Posted by dale_gribble Ok stock 3 then.

That's probably a lotta $$$ sitting in inventory that may not move for months...I doubt that would happen. For every one of these they stock, that's probably the value of 25 less expensive products that actually turnover quickly.

[EdgeAutosport.com]

Its actually not a bad idea to keep one around though. I'll talk it over with JP and see if we can make it happen.

[Scribbles]

Doubt they'd keep even 1 in stock. When does the warranty start? I'm guessing it's when you buy the block from the supplier rather than us buying it.

[EdgeAutosport.com]

Originally Posted by Scribbles Doubt they'd keep even 1 in stock. When does the warranty start? I'm guessing it's when you buy the block from the supplier rather than us buying it.

Okay, found out it starts 10 days after the order is placed. That will be the limiting factor in us keeping one in stock...

[ReddInc]

do they have an option for a new oil pan? Mine currently has a nice hole in it

Im planning on ordering a motor from someone, SOON. So far this looks like the option I want.

[speed23]

Originally Posted by ReddInc do they have an option for a new oil pan? Mine currently has a nice hole in it Im planning on ordering a motor from someone, SOON. So far this looks like the option I want.

In the OP it says they do for a few hundred more.

[ReddInc]

Ahh missed that part I guess

[EdgeAutosport.com]

Originally Posted by ReddInc do they have an option for a new oil pan? Mine currently has a nice hole in it Im planning on ordering a motor from someone, SOON. So far this looks like the option I want.

Yes, there is an option to add an oil pan and valve cover.

[dale_gribble]

I am at the point where I am shopping motor options and my car is down. This guy was definitely an option on my list but I just can't justify using the same OEM parts that failed on me already. Bent rods and cracked ringlands are still a possibility on these at modest power levels using OEM parts.

They really should have picked a modest upgrade for the rods and pistons.

[theurgy]

I think there are plenty of other options for buying a built motor (albeit much more expensive in this case).
To have an option for a stock, rebuilt to OEM specification engine at a reasonable price is always good.
I know many people (including myself) who are still just running basic bolt-ons with a proper tune that don't necessarily need to have a built engine.
While this option might not be exactly for you.. it's still a valid option.

[dale_gribble]

Understood. I just assume that if it happens once, it will happen again when they use the same parts. They should at least have used all of the latest parts/revs from Mazda including newer pistons which OP said they didn't.

There's a home for a $4,500 reman option with upgraded pistons/rods rated to ~400WHP between the pure OEM reman and the big build options. My guess is that option would be a good seller here on MSF.

[EdgeAutosport.com]

Originally Posted by dale_gribble Understood. I just assume that if it happens once, it will happen again when they use the same parts. They should at least have used all of the latest parts/revs from Mazda including newer pistons which OP said they didn't. There's a home for a $4,500 reman option with upgraded pistons/rods rated to ~400WHP between the pure OEM reman and the big build options. My guess is that option would be a good seller here on MSF.

It would be nice if the newer pistons were part of the reman'd long block but that is not up to us unfortunately. However there is an option that you just made me think of.

Providing you have a core...

MZR Reman Head - $1159
+
cp-e Stage 1 Short Block - $2999
----------------------
The makings of a built long block - $4158

Of course you would still need a motor build kit so you are going to be over $5k when all is said and done...

Regardless, the purpose of this Reman Long Block is to provide guys with a relatively quick solution to a bad situation. It comes with everything you need, timed, and ready to install so that you can get back up and running as quickly as possible. The warranty is a huge plus as well!

[bam88]

I got one of these motors and just got it settled in the car tonight. It all came very well packed and was pleasantly surprised to find all the gaskets it comes with. I would like to thank @EdgeAutosport.com; for all the help and recommendations made for this "build". I was wondering according to the ATK install "guide" they say prime the motor with oil, how is that done with our motors or it is even necessary?

[Goodrich27]

Originally Posted by bam88 I got one of these motors and just got it settled in the car tonight. It all came very well packed and was pleasantly surprised to find all the gaskets it comes with. I would like to thank @EdgeAutosport.com; for all the help and recommendations made for this "build". I was wondering according to the ATK install "guide" they say prime the motor with oil, how is that done with our motors or it is even necessary?

You turn the motor over without starting it. Turning the motor over will make the oil pump pump oil through the motor


Sent whilst bojanglen.

[theurgy]

Originally Posted by bam88 I got one of these motors and just got it settled in the car tonight. It all came very well packed and was pleasantly surprised to find all the gaskets it comes with. I would like to thank @EdgeAutosport.com; for all the help and recommendations made for this "build". I was wondering according to the ATK install "guide" they say prime the motor with oil, how is that done with our motors or it is even necessary?

LOL You had the whole engine out, why didn't you clean the engine bay before going through the trouble of reinstalling the new engine?
That engine bay looks nasty.

[EdgeAutosport.com]

Originally Posted by bam88 I got one of these motors and just got it settled in the car tonight. It all came very well packed and was pleasantly surprised to find all the gaskets it comes with. I would like to thank @EdgeAutosport.com; for all the help and recommendations made for this "build". I was wondering according to the ATK install "guide" they say prime the motor with oil, how is that done with our motors or it is even necessary?

You can either do like Goodrich27 said or there is a tool you can buy to prime it. Its a tank you can put about 4 quarts of oil in. You then pressurize it with air and feed it in where the sensor goes above the filter.

[bam88]

Originally Posted by theurgy LOL You had the whole engine out, why didn't you clean the engine bay before going through the trouble of reinstalling the new engine? That engine bay looks nasty.

I am on a tight time frame as this is my DD and I have to get back to work on Monday. If I had the time I would of loved to scrub everything down.

Originally Posted by Goodrich27 You turn the motor over without starting it. Turning the motor over will make the oil pump pump oil through the motor Sent whilst bojanglen.

Just to be 100% clear just cycle the key into the cranking stage a few times then start, or turn crank by hand?

[theurgy]

I think they mean cranking it by hand.

[bam88]

Does anybody know if these motors come with the timing pin installed??? Trying to crank motot by hand just before starting and it came to a stop and would not turn any more. Did not want to force it.

@EdgeAutosport.com;

[theurgy]

I wouldn't think they would have left a timing pin in.
Did you make sure to remove the spark plugs?

[qkrthnu2]

I'm in the market for a new motor. ( My MS6 BNR Stage 3 Install )
This looks like a great option!

@EdgeAutosport.com; I have some questions:

1. When adding this to the shopping cart on your site there is no way I see to specify the model year engine I want to order. You mentioned that you received the Gen 1 pistons, but that you also had specified it was for a 2006 car when ordering; is there a way to specify that I want a 2013 spec engine?

2. Along the same line of questioning. The GearheadEngines site says that "wear" items are discarded. I'm hoping the VVT actuator would be classified as a wear item. If Gen 1/random is the only option, can you verify that the VVT system is rebuilt using updated (i.e. post-TSB) parts?

3. Regarding the core refund, what is the time limit for core return?

4. Lastly, I love the 3 year unlimited mile warranty (daily driver MS6 ) and the no fault add-on! In the case of a ZZB , would the additional no-fault warranty be fulfilled by EdgeAutosport, GearheadEngines, or another company?

Thanks!

[EdgeAutosport.com]

Originally Posted by qkrthnu2 I'm in the market for a new motor. ( My MS6 BNR Stage 3 Install ) This looks like a great option! @EdgeAutosport.com; I have some questions: 1. When adding this to the shopping cart on your site there is no way I see to specify the model year engine I want to order. You mentioned that you received the Gen 1 pistons, but that you also had specified it was for a 2006 car when ordering; is there a way to specify that I want a 2013 spec engine? 2. Along the same line of questioning. The GearheadEngines site says that "wear" items are discarded. I'm hoping the VVT actuator would be classified as a wear item. If Gen 1/random is the only option, can you verify that the VVT system is rebuilt using updated (i.e. post-TSB) parts? 3. Regarding the core refund, what is the time limit for core return? 4. Lastly, I love the 3 year unlimited mile warranty (daily driver MS6 ) and the no fault add-on! In the case of a ZZB , would the additional no-fault warranty be fulfilled by EdgeAutosport, GearheadEngines, or another company? Thanks!

1. I checked and the part number is the same for all models through them so there is no way to differentiate between engine years. They are all the same in this case. You will likely not be able to get the gen 2 pistons this way...

2. I doubt the reuse the vvt actuator. I can't confirm that but on the one I purchased, it was brand new as were the cams.

3. I don't know that there is a time limit for core return though you probably shouldn't wait too long. I returned my core at the end of July after having purchased the engine in May.

4. Gearhead Engines or ATK Engines will be the ones to fulfill any warranty.

Let me know if you have any other questions!

Originally Posted by bam88 Does anybody know if these motors come with the timing pin installed??? Trying to crank motot by hand just before starting and it came to a stop and would not turn any more. Did not want to force it. @EdgeAutosport.com;

You shouldn't have to crank it by hand. To prime it, I believe you just have to floor the gas (which should shut off the injectors) while turning over the engine and it will crank but not start. This will allow it to pump oil pressure with out running the engine dry to start. There shouldn't be any timing pins in that would stop it from rotating.

[qkrthnu2]

Originally Posted by EdgeAutosport.com It also comes with the gaskets and stuff listed here.

@EdgeAutosport.com;

The "Fuel Injector O-ring"s listed there, were those new DISI injector seals or just the rubber O-ring for the fuel line connector side of the injector? Probably extremely wishful thinking on my part.

Thanks!

[bam88]

Originally Posted by qkrthnu2 @EdgeAutosport.com; The "Fuel Injector O-ring"s listed there, were those new DISI injector seals or just the rubber O-ring for the fuel line connector side of the injector? Probably extremely wishful thinking on my part. Thanks!

They are the smurf o-rings to go on the top of the injector and into the fuel rail.

[EdgeAutosport.com]

Originally Posted by qkrthnu2 @EdgeAutosport.com; The "Fuel Injector O-ring"s listed there, were those new DISI injector seals or just the rubber O-ring for the fuel line connector side of the injector? Probably extremely wishful thinking on my part. Thanks!

Just the blue o-ring that goes on top of the injector. Not the Injector seals.

[EdgeAutosport.com]

These engines have been pretty popular! Such an easy/quick way to get your car back on the road!

[BeastlyZoomZoom]

Originally Posted by EdgeAutosport.com These engines have been pretty popular! Such an easy/quick way to get your car back on the road!

Think my motor is going to go pretty soon have been looking into one of these as a replacement for awhile.

[Mistersix]

What a convenient option. Thanks Edge for making this available.

[jeopardy98]

Kudos yet again to you guys! You always are looking out for us.

[EdgeAutosport.com]

We are happy to help however we can!

[dale_gribble]

However you can? As in anything?

[EdgeAutosport.com]

Originally Posted by dale_gribble However you can? As in anything?

As in whatever is in our power to help with... Though I suppose we could loan out Nick if you need your lawn mowed or dogs walked or something...

[dale_gribble]

I have this medical condition where my scrotum has to be massaged and expressed daily. Does that fit into 'however you can'?

[EdgeAutosport.com]

Originally Posted by dale_gribble I have this medical condition where my scrotum has to be massaged and expressed daily. Does that fit into 'however you can'?

I'll have Nick get right on that!